Is the DSF010A a header or just the gasket?

Just the gasket — it's the seal between the head and the header or manifold. Confirm your engine's port pattern with the workshop before ordering.

Which cars does it suit?

It's listed for the Ford Falcon and Fairlane from 1960 to 1979. Confirm your exact engine with the workshop.

The recommended retail is $32.99. We fit it as part of header or manifold work at the Illawarra workshop.

DSF010A

Redback Header Gasket for Ford Falcon (01/1960 - 02/1979), Fairlane

Redback Redback Header Gasket.

BrandRedbackSWD

Category: Extractors and headers

RRP $32.99 AUD

In stock at supplier

Request fitted quote Call the workshop

Afterpay, Zip Pay & Zip Money available

Redback Header Gasket for Ford Falcon (01/1960 - 02/1979), Fairlane (0 product image

Part specs

Vehicle Make: Ford

The Redback DSF010A is a header gasket listed to fit the Ford Falcon (and Fairlane) built between 1960 and 1979. It's a low-cost service item at a recommended retail of $32.99.

What is a header gasket and what does it do?

A header gasket is the seal between the cylinder head and the header or exhaust manifold. It's the part that stops exhaust gas leaking at that joint, and it's a wear item — it's normally replaced whenever the manifold or headers come off. The DSF010A is the gasket only, not a header itself. There's no diameter, material or system spec to quote here because it's a sealing component; the workshop confirms it matches your engine's port pattern.

Will it suit my Falcon or Fairlane?

It's listed to fit the Ford Falcon and Fairlane from 1960 to 1979. Engines and port patterns changed across that long run, so the exact engine matters for the right gasket. Tell us what your car runs and we'll check the DSF010A against the listing before ordering.

When would I need this gasket?

You'd use a header gasket like this when fitting new headers, refitting a manifold, or chasing an exhaust leak at the head. It's an inexpensive part that's worth renewing any time the joint is opened up, rather than reusing an old seal.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men fits header gaskets like the DSF010A as part of header or manifold work in the Illawarra. We clean the head face, check it's flat and fit the new gasket before torquing the manifold or headers back down. Book the Falcon in and we'll match the gasket to your engine.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Is the DSF010A a header or just the gasket?: Just the gasket — it's the seal between the head and the header or manifold. Confirm your engine's port pattern with the workshop before ordering.
Which cars does it suit?: It's listed for the Ford Falcon and Fairlane from 1960 to 1979. Confirm your exact engine with the workshop.
How much is it?: The recommended retail is $32.99. We fit it as part of header or manifold work at the Illawarra workshop.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section

Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.

Unit 2/8 Shaban St, Albion Park Rail NSW 2527 02 4256 3740 sales@mufflermen.com.au Send vehicle details