K-AMB06036

Unbranded Exhaust System for Holden Barina (01/2004 - 02/2005)

Unbranded Exhaust System.

BrandUnbrandedSWD

Category: Complete exhaust systems

RRP $1555.00 AUD
Order in
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
Unbranded Exhaust System for Holden Barina (01/2004 - 02/2005) product image

Part specs

Fits Vehicle Year From
2004
Fits Vehicle Year From (Month)
01
Fits Vehicle Year To (Month)
12
Fits Vehicle Year To
2005
Vehicle Make
Holden
Coating
Zinc Plated
Tube Size (In)
051mm (2")
Tube Size
051mm (2")
Type
U-Bolt
Tube Size (Out)
051mm (2")

K-AMB06036 is an unbranded cat-back exhaust listed for the Holden Barina built 01/2004 to 02/2005, supplied through SWD. Recommended retail is $1,555.

What is K-AMB06036 and which Barina does it suit?

This is a cat-back system for the Holden Barina, pinned to a short 01/2004 to 02/2005 build window — a narrow slice that makes confirming your exact car important. The recommended retail of $1,555 is high for a small hatch, which is worth flagging up front so you can weigh it against the car. The part covers the rear exhaust run behind the catalytic converter.

What does a cat-back replace, and what does it leave alone?

It replaces the muffler and rear pipework from the catalytic converter back; it leaves the converter and the front pipework in place. So the emissions hardware the Barina left the factory with stays as it is, and the change is to the rear of the system and its note. SWD hasn't published a pipe diameter, material or muffler spec for this listing, so those remain unconfirmed until the kit is in hand.

Why so little published, and what does that mean for ordering?

Because it's unbranded, there's no manufacturer spec sheet — the blanks for diameter and material are genuine gaps in the supplier data. We verify those off the physical kit when it's matched to your Barina, and as a special-order line we check stock at the same time rather than assume it's available off the shelf. The $1,555 price is confirmed when you enquire.

What's the fitting process at our Illawarra workshop?

Oak Flats Muffler Men supplies and fits this in-house. The 01/2004 to 02/2005 window is the starting point, so we confirm your exact Barina before ordering — feed data can be imperfect. The system is then mounted up, hangers and underbody clearance checked, and the joints sealed before the car goes back to you.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Why is K-AMB06036 so expensive for a Barina?
The recommended retail is $1,555. That's high for a small hatch, so it's worth confirming the part and price with us before committing.
Which Barina does it fit?
It's listed for the Holden Barina built 01/2004 to 02/2005. Confirm your exact build with the workshop, as the window is short and variants matter.
Does it replace the catalytic converter?
No. It's a cat-back, so only the rear section is replaced and the converter stays in place.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.