HSV VE E2 Sedan Wagon 3in Catback Muffler
MPI AutomotiveRRP$4027.11HSV VE E2 Sedan Wagon 3in Catback Muffler/Muffler (SKU: SSMKHN0178) Engineered. Quality guaranteed.
View partMKHN0084
Holden Commodore VS Ute & WAG V6 3.8L 2.5in Catback Muffler/Tailpipe
Holden Commodore VS Ute & WAG V6 3.8L 2.5in Catback Muffler/Tailpipe.
BrandMantaMPI Automotive
Category: Mufflers and resonators
RRP $725.01 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- MKHN0084
- Supplier
- MPI Automotive
- Category
- Mufflers and resonators
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
Built for the earlier VS-series Holden Commodore, the MPI Automotive MKHN0084 is a 2.5in cat-back for the V6 3.8L ute and wagon. It runs a single muffler into a tailpipe — a tidy single-stage replacement for the factory system on these older bodies.
What suits the VS 3.8L V6?
The VS is the older platform here, and its 3.8L V6 ute and wagon take a system routed for that body. The MKHN0084 is a 2.5in cat-back with a single muffler feeding a tailpipe — the 2.5in bore matches the 3.8L V6's output, holding gas speed up for low-down and mid-range response. With one muffler in the line it's a clean single-stage system, well suited to refreshing tired original pipework on a long-serving car.
Why a muffler-and-tailpipe layout?
One muffler does the silencing, then the pipe runs out to the tail — a single stage rather than a doubled muffler run. On the 3.8L V6 that sets a measured note without over-boxing the system. It stays a cat-back, so the catalytic converter and front pipework are retained as the factory fitted them; only the section behind the cat is replaced. We can't quote a sound figure; a comparable fit is the honest gauge.
Will it fit my VS ute or wagon?
It's listed to fit the Holden Commodore VS V6 3.8L in ute and wagon body. The tray and wagon rear floor route differently, and this system covers both; confirm your exact build with the workshop before ordering, as these older cars can carry repair history that affects fitment.
How do we fit it at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits the MKHN0084 in-house across the Illawarra. We hang the muffler on the car's mounts, check clearance to the tray or rear floor for your body, and join it square front and rear — and on an older car we check the hangers and flanges it joins to. Bring the car in and we'll confirm fitment and book the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- Which engine is the MKHN0084 for?
- The Holden Commodore VS V6 3.8L in ute and wagon body.
- What bore and layout is it?
- It's a 2.5in cat-back with a single muffler into a tailpipe — one silencing stage.
- Does it keep the catalytic converter?
- Yes — as a cat-back, the factory converter and front pipework stay in place.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More mufflers and resonators the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
Holden Commodore VE Ute & Maloo V8 3in Catback Muffler
MPI AutomotiveRRP$3830.49Holden Commodore VE Ute & Maloo V8 3in Catback Muffler/Muffler (SSMKHN0196) Fits HOLDEN. Fast.
View part
Holden Commodore VE V8 Sedan Wagon 3in Catback Muffler
MPI AutomotiveRRP$3830.49Holden Commodore VE V8 Sedan Wagon 3in Catback Muffler/Muffler (SSMKHN0170) Fits HOLDEN. Fast.
View part
HSV VE E2 Sedan Wagon 3in Catback Hotdog/Muffler
MPI AutomotiveRRP$3812.47HSV VE E2 Sedan Wagon 3in Catback Hotdog/Muffler (SKU: SSMKHN0179) Engineered. Quality guaranteed.
View part
VF HSV Ute Maloo V8 3in CatBack Muffler
MPI AutomotiveRRP$3749.44VF HSV Ute Maloo V8 3in CatBack Muffler/Muffler (SSMKHN0337) Fits HOLDEN. Fast shipping, warranty included.
View part
VF HSV V8 Sedan Wagon 3in Catback Muffler
MPI AutomotiveRRP$3749.44VF HSV V8 Sedan Wagon 3in Catback Muffler/Muffler (SKU: SSMKHN0333) Engineered. Quality guaranteed.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.