holden-commodore-ve-vf-v6-v8-ute-2-1-2-kit-with-2-x-hotdog-xpipe-4-x-sc-tips

HOLDEN COMMODORE VE, VF V6 V8 UTE AND STATESMAN WM WN 2 1/2" KIT WITH 2 x HOTDOG - XPIPE

HOLDEN COMMODORE VE, VF V6 V8 UTE AND STATESMAN WM WN 2 1/2" KIT WITH 2 x HOTDOG - XPIPE & 4 X SC.

DistributorExhaust Systems Australia

Category: Mufflers and resonators

RRP $1315.00 AUD
Confirmed on order
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
HOLDEN COMMODORE VE, VF V6 V8 UTE AND STATESMAN WM WN 2 1/2" KIT WITH 2 x HOTDOG - XPIPE & 4 X SC TIPS product image

Part specs

SKU
holden-commodore-ve-vf-v6-v8-ute-2-1-2-kit-with-2-x-hotdog-xpipe-4-x-sc-tips
Supplier
Exhaust Systems Australia
Category
Mufflers and resonators
Stock status
Confirmed on order

Twin hotdogs, an X-pipe and four SC tips make up the HOLDEN-COMMODORE-VE-VF-V6-V8-UTE-2-1-2-KIT-WITH-2-X-HOTDOG-XPIPE-4-X-SC-TIPS, a 2in kit listed to fit the Holden Commodore VE-VF V6 and V8 ute and the Statesman WM-WN.

What do the twin hotdogs and X-pipe do?

Supplied by Exhaust Systems Australia, two hotdog resonators give two stages of compact straight-through drone control, and the X-pipe crosses the system so pulses balance across the banks. On a V6 or V8 ute the pairing aims for a balanced, drone-managed note with flow kept up, finished by four SC tips at the rear. It is the crossover quad-tip build, here in the SC-tip finish.

What's in the kit?

This is a 2in kit built as a complete rear package: two hotdog resonators, the X-pipe crossover and four SC tips. The listing also covers the Statesman WM-WN, so it spans the long-wheelbase platform alongside the ute.

Will it suit my VE-VF ute or WM-WN Statesman?

It is listed to fit the Holden Commodore VE-VF V6 and V8 ute and the Statesman WM-WN. Ute and Statesman bar exits differ, so confirm your exact body, engine and tip cut-outs with the workshop before ordering.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men fits these crossover kits across the Illawarra. We set both hotdogs and the X-pipe for clearance, then align the four SC tips evenly to the rear before final hang. At $1315 it is a full crossover build; the material is not published by the supplier, so we verify the kit against your ute or Statesman before any cutting.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

What tips does this kit use?
Four SC tips, finishing the rear. Tip alignment depends on your VE-VF ute or WM-WN bar exits, which we set at fitting.
Does it fit the Statesman?
It is listed to fit both the VE-VF ute and the WM-WN Statesman. Confirm your exact body and engine with the workshop.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.