Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partHOLK128U25-134C
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 2.5in Full System 1 3/4in HPC
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 2.5in Full System 1 3/4in HPC Extractor 3.5in Tip.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $6221.49 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- HOLK128U25-134C
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive HOLK128U25-134C is a ceramic-coated 1-3/4in extractor set on a dual 2.5in full system with a 3.5in tip, listed to fit the Holden Commodore VE-VF V8 Ute (and the WM-WN Caprice). It's the smaller-primary, coated option in this header range.
What does this extractor package cover?
This is a full header-back package: 1-3/4in tubular extractors replacing the cast factory manifolds, a dual 2.5in system running back from the collectors, and a 3.5in tip at the rear. Extractors give each cylinder its own primary pipe before merging, which can ease exhaust flow off a V8 head compared with a cast manifold. The 1-3/4in primaries here are the smaller of the two sizes in this range; the larger uses 1-7/8in tubes.
What's a ceramic-coated header and what does it change?
The "134C" marks the HPC-style ceramic coating on the 1-3/4in primaries. Header coatings are applied to the steel to manage surface heat and resist corrosion. The supplier hasn't published a coating temperature or service-life figure, so we won't quote one — what the coating changes versus the bare set is the finish on the tubes, not the 2.5in sizing, the 3.5in tip, or the V8 fitment.
Will it suit my Holden Commodore?
It's listed to fit the Holden Commodore VE-VF V8 in Ute form, and the WM-WN Caprice is covered by the same listing. The years aren't published in our record, and V8 Commodore builds vary across that run, so confirm your exact variant with the workshop before ordering — header fitment leaves little margin for guesswork.
What does fitting involve at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits coated extractor sets like this in-house across the Illawarra. The job covers clearances, gaskets and the full dual 2.5in run through to the 3.5in tip. At $6,221.49 RRP it's a special-order item — send us your build and we'll confirm fitment and book the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- How is the HOLK128U25-134C different from the 1-7/8in version?
- This set uses 1-3/4in primaries with a ceramic coating; the 178 versions in the range use larger 1-7/8in tubes. Both share the dual 2.5in system and VE-VF V8 fitment.
- Does it fit the Caprice too?
- Yes — it's listed to fit the Holden Commodore VE-VF V8 Ute and the WM-WN Caprice. Confirm your exact variant with the workshop before ordering.
- Can you fit it in the Illawarra?
- Yes, Oak Flats Muffler Men supplies and fits sets like this in-house. It's a special-order item at $6,221.49 RRP, so contact us to confirm fitment first.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.