Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partHOLK128U3-178
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System, 1 7/8in Extractors
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System, 1 7/8in Extractors, 3.5in Tips.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $5972.01 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- HOLK128U3-178
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive HOLK128U3-178 is a dual 3in full system on 1-7/8in extractors, finishing in 3.5in tips, listed to fit the Holden Commodore VE-VF V8 ute and WM-WN Caprice. It is an extractor-based full exhaust system that swaps the factory cast manifolds for tubular runners.
What's an extractor and what does it change?
Extractors (also called headers) replace the cast factory manifolds with separate tubular runners off each cylinder, to let the engine breathe out with less restriction than the castings allow. It is a change to the exhaust side of the engine, not an internal part. This set runs 1-7/8in primary tubes. It finishes in 3.5in tips. The trade-off is the labour to drop the manifolds and fit it cleanly.
What does this system include?
This is a full system, not a single bolt-on — a dual 3in full system on 1-7/8in extractors, finishing in 3.5in tips. The dual layout runs a pipe down each side. Material and sound figures are not published by MPI Automotive, so we do not state them. It is listed at $5,972.01 AUD and, being built to the vehicle, is normally a special-order item we bring in for your car.
Will it suit my Holden Commodore VE-VF V8 ute and WM-WN Caprice?
The HOLK128U3-178 is listed to fit the Holden Commodore VE-VF V8 ute and WM-WN Caprice — treat that as "listed to fit" rather than a promise, since feed data can be imperfect. Confirm your exact build, engine and suspension with the workshop before ordering, since an extractor system is a significant fitment that must match the car. Year coverage is not published, so we go by the model designation.
What does fitting involve at our Illawarra workshop?
Oak Flats Muffler Men fits extractor systems like the HOLK128U3-178 in-house across the Illawarra. The job means access to drop the factory manifolds, fresh gaskets on assembly, and matching the 3in pipework so it hangs and seals. Send your car's details and we will confirm the fit, check NSW road compliance, and book the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- What does the HOLK128U3-178 fit?
- It is listed to fit the Holden Commodore VE-VF V8 ute and WM-WN Caprice. Confirm your exact build and engine with the workshop before ordering.
- What size are the headers?
- They use 1-7/8in primary tubes, with the system at 3in and 3.5in tips.
- Can Oak Flats Muffler Men fit it?
- Yes. We fit it in-house in the Illawarra, drop the factory manifolds, fit fresh gaskets and check it seals and clears before it leaves the bay.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.