Will the K-RPD14608 fit my Holden Commodore?

It's listed to fit the Holden Commodore from 04/1995. Fitment data can be imperfect, so confirm your exact variant and build year with the workshop before ordering.

Why is it priced higher than some other Commodore cat-backs?

Its RRP is $2,732.34, at the upper end of this range. We list it at the supplier's recommended retail; the workshop confirms current price and availability when you book.

Does it touch the catalytic converter?

No. As a cat-back it replaces the run from the converter rearward, so the factory cat and front pipework stay in place.

K-RPD14608

Redback Performance Exhaust System for Holden Commodore

Redback Performance Exhaust System.

BrandRedbackSWD

Category: Complete exhaust systems

RRP $2732.34 AUD

Order in

Request fitted quote Call the workshop

Afterpay, Zip Pay & Zip Money available

Redback Performance Exhaust System for Holden Commodore (04/1995 - 199 product image

Part specs

Coating: Premium Heat-Proof Paint
Cat Option: With Cat
Transmission: Auto
Header Design: Tri-Y
Muffler Option: With Centre & Rear Muffler
Tube Size: 063mm (2 1/2")
System Layout: Engine Back System
Vehicle Make: Holden
Fitting Time [min.]: 240
Header Secondary Size: 045mm (1 3/4")
Header Primary Size: 041mm (1 5/8")
Fits Power Steering: Yes
EGR Fitting: N/A
Header Outlet Size: 063mm (2 1/2")
Fits With Air Conditioning: Yes
Length: 133mm
Width: 98
Pack Size: 10
Inside Diameter: 65mm
Tube Size (In): 067mm (2 5/8")
Type: U-Bolt
Tube Size (Out): 067mm (2 5/8")

Carrying a $2,732.34 RRP, the Redback K-RPD14608 is one of the dearer Commodore cat-backs in this range — listed for the Holden Commodore from 04/1995 and fitted at Oak Flats Muffler Men in the Illawarra.

What sets this Commodore listing apart?

The K-RPD14608 is pinned to the Holden Commodore from 04/1995 — a specific start point in the model's run, and worth matching against your build because Commodore exhaust architecture shifted across the '90s. At $2,732.34 it sits at the upper end of the Commodore cat-backs we list. That price is the one published hard figure; pipe diameter, material and muffler configuration aren't given, so we confirm those off the kit rather than quote them.

What does a cat-back actually replace?

A cat-back is the rear half of the system — everything from behind the catalytic converter to the tailpipe. Swapping it renews the rear pipework and changes the note while the factory cat and front pipes stay put. It's the lower-disruption end of the exhaust-upgrade scale, the path you take when you want a freer-flowing rear section without touching the emissions hardware up front.

Will it suit my Commodore?

It's listed to fit the Holden Commodore from 04/1995, drawn from supplier fitment data — so read that as listed-to-fit, not a cast-iron guarantee. Builds vary across a model range and feed data can be imperfect, so send your exact variant, build year and engine and we'll check it against the listing before anything is ordered.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men supplies and fits cat-backs like this in-house across the Illawarra, so the workshop that orders the part is the one that hangs it and checks the clearances. Given the spend, we confirm the K-RPD14608 against your Commodore first, then book the hoist.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Will the K-RPD14608 fit my Holden Commodore?: It's listed to fit the Holden Commodore from 04/1995. Fitment data can be imperfect, so confirm your exact variant and build year with the workshop before ordering.
Why is it priced higher than some other Commodore cat-backs?: Its RRP is $2,732.34, at the upper end of this range. We list it at the supplier's recommended retail; the workshop confirms current price and availability when you book.
Does it touch the catalytic converter?: No. As a cat-back it replaces the run from the converter rearward, so the factory cat and front pipework stay in place.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section

Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.

Unit 2/8 Shaban St, Albion Park Rail NSW 2527 02 4256 3740 sales@mufflermen.com.au Send vehicle details