Will the K-RPM14667 fit my 1995 Holden Commodore?

It is listed to fit the Holden Commodore from 1995. Confirm your exact variant with the workshop first, as fitment data can be imperfect.

Is the catalytic converter included?

No. As a cat-back, the K-RPM14667 replaces everything behind the converter and leaves the cat and front pipe in place.

The K-RPM14667 is listed at $2639.75 and is usually brought in to order; we confirm availability before you commit.

K-RPM14667

Redback Performance Exhaust System for Holden Commodore

Redback Redback Performance Exhaust System.

BrandRedbackSWD

Category: Complete exhaust systems

RRP $2639.75 AUD

Order in

Request fitted quote Call the workshop

Afterpay, Zip Pay & Zip Money available

Redback Performance Exhaust System for Holden Commodore (04/1995 - 12/ product image

Part specs

Transmission: Manual
Header Design: Tri-Y
Cat Option: With Cat
Muffler Option: With Centre & Rear Muffler
Coating: Premium Heat-Proof Paint
Tube Size: 063mm (2 1/2")
System Layout: Engine Back System
Vehicle Make: Holden
Fitting Time [min.]: 240
Fits With Air Conditioning: Yes
Fits Power Steering: Yes
Header Secondary Size: 045mm (1 3/4")
EGR Fitting: N/A
Header Outlet Size: 063mm (2 1/2")
Header Primary Size: 041mm (1 5/8")
Length: 133mm
Width: 98
Pack Size: 10
Inside Diameter: 65mm
Tube Size (In): 067mm (2 5/8")
Type: U-Bolt
Tube Size (Out): 067mm (2 5/8")

The Redback K-RPM14667 is a cat-back exhaust listed to fit the Holden Commodore from 1995, with an RRP of $2639.75. It replaces the system from the catalytic converter rearward as one kit.

Where does the K-RPM14667 sit in the system?

This is a cat-back, so it begins at the catalytic converter and runs to the tailpipe: intermediate pipe, mufflers and the rear section. Everything ahead of the cat, including the converter itself, is left as standard. It sits between a tailpipe-only change and a full engine-back rebuild, replacing the part of the system that ages worst while leaving the harder-to-reach front pipework alone. For a mid-1990s Commodore that means a complete rear renewal without touching the emissions gear up front. Redback list no diameter or material grade for it, so we do not quote either.

Will it suit my Holden Commodore?

It is listed to fit the Holden Commodore from 1995. Fitment data on cars this age is not always exact, so we go through the model, body and any past exhaust repairs with you before ordering the K-RPM14667, so it mates cleanly to the converter flange. A Commodore that has had earlier exhaust work can sit slightly differently to a factory-original car, which is exactly the kind of detail we want to catch before the part is ordered in.

Does a cat-back change how the car sounds?

Renewing the rear silencing usually gives a cleaner, slightly fuller note than a worn factory muffler. The exact result varies with the car and Redback publish no measured sound figures, so we will not quote a level.

What does fitting involve at Oak Flats?

Our Illawarra workshop fits cat-back systems like this on the hoist, checking hangers, clearances and the cat joint before signing off. At $2639.75 the K-RPM14667 is generally ordered in for these older Commodores, so we confirm stock before you commit.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Will the K-RPM14667 fit my 1995 Holden Commodore?: It is listed to fit the Holden Commodore from 1995. Confirm your exact variant with the workshop first, as fitment data can be imperfect.
Is the catalytic converter included?: No. As a cat-back, the K-RPM14667 replaces everything behind the converter and leaves the cat and front pipe in place.
How much is it?: The K-RPM14667 is listed at $2639.75 and is usually brought in to order; we confirm availability before you commit.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section

Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.

Unit 2/8 Shaban St, Albion Park Rail NSW 2527 02 4256 3740 sales@mufflermen.com.au Send vehicle details