K-RPM15640

Redback Performance Exhaust System for Holden Commodore

Redback Performance Exhaust System

BrandRedbackSWD

Category: Complete exhaust systems

RRP $2507.04 AUD
Order in
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
Redback Performance Exhaust System for Holden Commodore (03/1990 - 06/ product image

Part specs

Cat Option
With Cat
System Layout
Engine Back System
Header Design
Tuned
Coating
Premium Heat-Proof Paint
Tube Size
063mm (2 1/2")
Muffler Option
Centre Muffler Only (Medium)
Transmission
Auto
Vehicle Make
Holden
Fitting Time [min.]
240
Header Secondary Size
045mm (1 3/4")
Header Primary Size
041mm (1 5/8")
Fits Power Steering
Yes
EGR Fitting
N/A
Header Outlet Size
063mm (2 1/2")
Fits With Air Conditioning
Yes
Length
133mm
Width
98
Pack Size
10
Inside Diameter
65mm
Tube Size (In)
067mm (2 5/8")
Type
U-Bolt
Tube Size (Out)
067mm (2 5/8")

Redback list the K-RPM15640 to fit the Holden Commodore from 1990, at an RRP of $2507.04. It is a cat-back exhaust, covering the system from the catalytic converter back to the tailpipe.

Does a cat-back change how the Commodore sounds?

Fitting fresh rear silencing in place of a worn factory muffler usually gives a fuller note, though the exact result depends on the car. Redback publish no sound measurements for the K-RPM15640, so we describe the change honestly rather than quoting a decibel level. Because only the section behind the converter is renewed, the difference is a refreshed rear note rather than a reworking of the whole exhaust.

Will it suit my Holden Commodore?

It is listed to fit the Holden Commodore from 1990. Fitment listings for cars this age can be imperfect, so we confirm the Commodore's model, body and any earlier exhaust repairs before ordering the K-RPM15640 in, checking it lines up at the converter.

What does a cat-back replace?

A cat-back is the rear run of the exhaust: the intermediate pipe, mufflers and tailpipe behind the catalytic converter. The cat and front pipe are left standard, so the K-RPM15640 renews the corroded rear half without touching the emissions hardware. Redback list no diameter or material grade for it.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men fit it on the hoist, checking the converter joint, hangers and tailpipe clearance before signing off. At $2507.04 it is generally ordered in for these older Commodores, so we confirm stock first.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Will the K-RPM15640 fit my Holden Commodore?
It is listed to fit the Holden Commodore from 1990. Confirm your exact variant with the workshop first, as fitment data can be imperfect.
Is the catalytic converter replaced?
No. It is a cat-back, so the converter and front pipe stay in place and the pipework behind them is renewed.
Is it a stock item?
It is listed at $2507.04 and is usually ordered in; we confirm availability before you commit.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.