Does the K-RPT14597 fit my Commodore?

It is listed to fit the Holden Commodore from 01/1988. Confirm your exact engine and build with the workshop first.

Will it be louder than standard?

A cat-back usually changes the note over a tired factory muffler, but no sound data is published, so we will not quote a figure.

What does it cost to supply?

The recorded RRP is $2,493.75 (AUD). As an older part it is often ordered in; we confirm availability when you enquire.

K-RPT14597

Redback Performance Exhaust System for Holden Commodore

Redback Redback Performance Exhaust System.

BrandRedbackSWD

Category: Complete exhaust systems

RRP $2493.75 AUD

Order in

Request fitted quote Call the workshop

Afterpay, Zip Pay & Zip Money available

Redback Performance Exhaust System for Holden Commodore (01/1988 - 03/ product image

Part specs

Tube Size: 063mm (2 1/2")
Header Design: Tri-Y
Muffler Option: Centre Muffler Only (Medium)
Cat Option: With Cat
Coating: Premium Heat-Proof Paint
Transmission: Auto
System Layout: Engine Back System
Vehicle Make: Holden
Fitting Time [min.]: 240
Header Secondary Size: 045mm (1 3/4")
Header Primary Size: 041mm (1 5/8")
Fits Power Steering: Yes
EGR Fitting: N/A
Header Outlet Size: 063mm (2 1/2")
Fits With Air Conditioning: Yes
Length: 133mm
Width: 98
Pack Size: 10
Inside Diameter: 65mm
Tube Size (In): 067mm (2 5/8")
Type: U-Bolt
Tube Size (Out): 067mm (2 5/8")

The Redback K-RPT14597 is a cat-back performance exhaust listed to fit the Holden Commodore from 01/1988, supplied through SWD with a recommended retail of $2,493.75.

Will it suit my Holden Commodore?

This system is listed for the Holden Commodore from 01/1988. That early build date is the first thing we check, because the Commodore ran several engine and body combinations through the late 1980s and the right cat-back depends on which one is under your car. Treat the listing as listed to fit, not a promise of fit, and send your exact variant so we can match the K-RPT14597 before anything is ordered.

What is a cat-back and what does it actually change?

A cat-back is the run of pipe and silencing behind the catalytic converter. Fitting one renews the rear half of the exhaust and changes the note relative to a worn factory muffler, but it leaves the converter and front pipe as they came from the factory — so it is not a change to anything ahead of the cat. On a Commodore from the late 1980s the honest value is usually fresh, complete rear metal rather than any figure we could quote, and we do not publish power or sound data for this part.

What does this listing include and cost?

The K-RPT14597 is the cat-back package — intermediate pipe, mufflers and tailpipe from the converter rearward. The recorded recommended retail is $2,493.75. Redback does not publish a diameter, material or muffler layout for this listing in our data, so those details are confirmed against the part rather than stated here.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men fits Redback cat-back systems in-house across the Illawarra. The car goes on the hoist, we check the flange to the existing cat, the hangers and the clearances, and as a vintage Holden fitment we confirm stock before ordering and booking the bay.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Does the K-RPT14597 fit my Commodore?: It is listed to fit the Holden Commodore from 01/1988. Confirm your exact engine and build with the workshop first.
Will it be louder than standard?: A cat-back usually changes the note over a tired factory muffler, but no sound data is published, so we will not quote a figure.
What does it cost to supply?: The recorded RRP is $2,493.75 (AUD). As an older part it is often ordered in; we confirm availability when you enquire.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section

Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.

Unit 2/8 Shaban St, Albion Park Rail NSW 2527 02 4256 3740 sales@mufflermen.com.au Send vehicle details