Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partMKHN0328
Holden Commodore VF V8 Sedan Wagon 2.5in With Extractors Hotdog/Muffler
Holden Commodore VF V8 Sedan Wagon 2.5in With Extractors Hotdog/Muffler.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $4759.17 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- MKHN0328
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive MKHN0328 is the 2.5in extractor-and-exhaust package for the Holden Commodore VF V8 sedan, built around a single hotdog muffler. The 2.5in sizing is the point of difference here: the tighter-bore street build that keeps gas speed up rather than chasing the biggest pipe.
Why a 2.5in system on the VF V8?
At 2.5in this is the keener-bore option in MPI's VF extractor range. A 2.5in run holds exhaust velocity better than a larger pipe through the lower and middle rev range where a road-driven V8 spends most of its time, so it favours response and tractability over outright top-end flow. It pairs that with a hotdog muffler, a compact straight-through silencer that lifts the note over stock without the bulk of a full chambered box. For a daily-driven VF sedan, it's the restrained, drivable end of the range.
What does the package replace?
This is a header-back overhaul: it starts at the cylinder heads with tuned-length extractors that swap out the factory cast manifolds, then carries through to the matched 2.5in exhaust and its hotdog muffler. The cast manifolds and the original VF pipework both come out and are replaced as one MKHN0328 set, so the system flows as a designed whole rather than a part-pipe patch.
Will it suit my VF Commodore?
It's listed to fit the Holden Commodore VF V8 sedan. Because an extractor system is tied to a specific body and driveline, the exact build matters: send your VF details and the workshop confirms fitment, including how the 2.5in run clears the floor on your car, before anything is ordered.
What's involved fitting it at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits MPI extractor packages like the MKHN0328 in-house across the Illawarra. Header work means pulling the factory manifolds, fitting the primaries, then hanging the 2.5in run and hotdog muffler and checking clearances under the floor. At an RRP of $4,759.17 it's a special-order set, so we confirm the fitment and lead time with you before booking the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- What size is the MKHN0328 system?
- It's a 2.5in system, the tighter-bore VF option that keeps gas speed up for low and mid-range response, paired with a hotdog muffler.
- Will it fit my VF V8 sedan?
- It's listed to fit the Holden Commodore VF V8 sedan. Confirm your exact build with the workshop before ordering, as extractor systems are tied to the body and driveline.
- What does the hotdog muffler do?
- A hotdog is a compact straight-through silencer; it lifts the note over stock without the bulk of a full chambered muffler.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.