Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partMKHN0410
Holden Commodore VU VY VZ V8 Ute 3in Dual With 1 3/4 in Extractors Muffler/Tailpipe
MPI Automotive Holden Commodore VU VY VZ V8 Ute 3in Dual With 1 3/4 in Extractors Muffler/Tailpipe.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $4329.64 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- MKHN0410
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive MKHN0410 is a 3in dual extractor-and-exhaust package on 1-3/4in primary extractors, listed to fit the Holden Commodore VU, VY and VZ V8 ute. It runs a rear muffler out to a tailpipe, so it's a header-back overhaul rather than a tailpipe-only swap.
What does this extractor system cover?
This is a header-back package for the VU, VY and VZ V8 ute. It begins at the cylinder heads with 1-3/4in primary extractors and runs a 3in dual exhaust through a rear muffler out to a tailpipe. The factory cast manifolds and original pipework both come out, replaced as one matched MKHN0410 kit. With a single rear muffler rather than a resonator-plus-muffler chain, it's the simpler of the layouts MPI lists for these utes.
What's an extractor and what does it change?
Extractors are tuned-length headers that replace the cast manifolds the V8 ships with. Each cylinder getting its own primary tube before the merge lowers back-pressure and helps the engine clear spent gas. The honest trade-offs are heat exposure in the bay, a longer fit than a bolt-on muffler, and a changed note. Here the 1-3/4in primaries feed a 3in dual run finishing through a muffler and tailpipe, sized to flow as a matched set.
Will it suit my VU, VY or VZ ute?
It's listed to fit the Holden Commodore VU, VY and VZ V8 ute. Because an extractor system is tied to the specific body and driveline, the exact build matters: send your ute's details and the workshop will confirm fitment before anything is ordered.
What does fitting involve at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits MPI extractor packages like the MKHN0410 in-house across the Illawarra. The work means removing the factory manifolds, fitting the primaries, then hanging the 3in dual muffler-and-tailpipe run and checking clearances along the floor and over the rear axle. At an RRP of $4,329.64 it's a special-order set, so we confirm fitment and lead time with you before booking the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- Which utes does the MKHN0410 fit?
- It's listed to fit the Holden Commodore VU, VY and VZ V8 ute. Confirm your exact build with the workshop before ordering.
- How is this layout different from the other VU/VY/VZ kits?
- This one runs a single rear muffler out to a tailpipe rather than adding a resonator, making it the simpler muffler layout in the range.
- Is this a full system or just the headers?
- It's a header-back package: 1-3/4in primary extractors plus a 3in dual exhaust with a muffler and tailpipe, supplied as one matched MKHN0410 kit.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.