Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partMKHN0412
Holden Commodore VU VY VZ V8 Ute 3in L & R With 1 3/4 in Extractors Hotdog/Muffler
Holden Commodore VU VY VZ V8 Ute 3in L & R With 1 3/4 in Extractors Hotdog/Muffler.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $4722.37 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- MKHN0412
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive MKHN0412 is a 3in extractor-and-exhaust package built around 1-3/4in primary extractors, listed to fit the Holden Commodore VU, VY and VZ V8 ute. It runs left-and-right pipes with a hotdog-plus-muffler layout, so it's a header-back overhaul rather than a tailpipe swap.
What does this extractor system cover?
This is a header-back package: it starts at the cylinder heads with 1-3/4in primary extractors and carries through to a 3in exhaust split into left and right pipes, running a hotdog resonator ahead of the main muffler. On a VU–VZ V8 ute, that means the factory cast manifolds and the original pipework both come out, replaced as one matched MKHN0412 kit. The L and R layout routes each bank down its own side of the floor.
What's an extractor and what does it change?
Extractors (tuned-length headers) replace the restrictive cast-iron manifolds the V8 left the factory with. By giving each cylinder its own primary tube before they merge, they reduce back-pressure and help the engine scavenge spent gas more cleanly. The trade-off is honest: headers sit in the engine bay heat zone, take longer to fit than a bolt-on muffler, and change the exhaust note. The 1-3/4in primary size here is matched to the 3in downstream pipework so the system flows as a set.
Will it suit my VU, VY or VZ ute?
It's listed to fit the Holden Commodore VU, VY and VZ V8 ute. Because it's an extractor-based system tied to a specific body and driveline, the exact build matters: send your ute's series and details and the workshop will confirm the fitment before anything is ordered.
What does fitting involve at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits MPI extractor packages like the MKHN0412 in-house across the Illawarra. Header work means removing the factory manifolds, fitting the primaries, then hanging the 3in left-and-right hotdog-and-muffler run and checking clearances along the floor and over the rear axle. At an RRP of $4,722.37 it's a special-order set, so we confirm the fitment and lead time with you before booking the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- Will the MKHN0412 fit my VU/VY/VZ Commodore ute?
- It's listed to fit the Holden Commodore VU, VY and VZ V8 ute. Confirm your exact series and build with the workshop before ordering, as extractor systems are tied to the specific body and driveline.
- What's the L and R layout?
- It runs left and right pipes — the exhaust splits into two sides down the floor — with a hotdog resonator ahead of the main muffler. A twin-muffler variant is offered separately.
- Is this a full system or just the headers?
- It's a header-back package: 1-3/4in primary extractors plus a 3in left-and-right exhaust with a hotdog and muffler, supplied as one matched MKHN0412 kit.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.