Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6639.02MPI Automotive Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 7/8in HPC Extractors 3.5in Tips.
View partMKHN0423
Holden Commodore VE V8 Sedan Wagon 3in With 1 3/4 in Extractors Hotdog/Muffler
Holden Commodore VE V8 Sedan Wagon 3in With 1 3/4 in Extractors Hotdog/Muffler (MKHN0423) Fits HOLDEN.
BrandMantaMPI Automotive
Category: Extractors and headers
RRP $4676.00 AUD
In stock at supplierAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- MKHN0423
- Supplier
- MPI Automotive
- Category
- Extractors and headers
- Vehicle fitment
- Holden
- Stock status
- In stock at supplier
The MPI Automotive MKHN0423 is a 3in extractor-and-exhaust package on 1-3/4in primary extractors, listed to fit the Holden Commodore VE V8 in sedan and wagon body styles. It runs a hotdog resonator into a rear muffler, so it's a header-back overhaul rather than a tailpipe swap.
What does this extractor system cover?
This is a header-back package for the VE Commodore V8. It starts at the cylinder heads with 1-3/4in primary extractors and carries a 3in exhaust through a hotdog resonator into a rear muffler. The factory cast manifolds and original pipework both come out, replaced as one matched MKHN0423 kit. The hotdog-plus-muffler layout trims resonance while opening the V8 up compared with the restrictive stock manifolds.
What's an extractor and what does it change?
Extractors are tuned-length headers that replace the cast manifolds the V8 ships with. Giving each cylinder its own primary tube before the merge lowers back-pressure and helps the engine scavenge spent gas. The honest trade-offs are heat exposure in the bay, a longer fit than a bolt-on muffler, and a changed note versus stock. The 1-3/4in primaries here are matched to the 3in downstream pipe so the system flows as one set across the sedan and wagon.
Will it suit my Holden Commodore VE?
It's listed to fit the Holden Commodore VE V8 in sedan and wagon form. Because an extractor system is tied to the specific body and driveline, the exact build matters: send your VE details and the workshop will confirm fitment before anything is ordered.
What does fitting involve at our Illawarra workshop?
Oak Flats Muffler Men supplies and fits MPI extractor packages like the MKHN0423 in-house across the Illawarra. The job means pulling the factory manifolds, fitting the primaries, then hanging the 3in hotdog-and-muffler run and checking clearances down the floor. At an RRP of $4,676 it's a special-order set, so we confirm fitment and lead time with you before booking the bay.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- Does the MKHN0423 suit both the sedan and the wagon?
- Yes, it's listed to fit the Holden Commodore VE V8 in sedan and wagon body styles. Confirm your exact build with the workshop before ordering.
- Is this a full system or just the headers?
- It's a header-back package: 1-3/4in primary extractors plus a 3in exhaust with a hotdog and muffler, supplied as one matched MKHN0423 kit.
- Is there a quieter version available?
- A twin-muffler variant is offered separately for the VE V8 if you prefer the quieter of the two layouts.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6639.02MPI Automotive DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 78in headers, 3.5in tips.
View part
Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6550.21MPI Automotive Holden DPE VF HSV LSA V8 Sedan & Wagon dual 3in full system with 1 7/8in coated headers.
View part
DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated
MPI AutomotiveRRP$6502.43DPE Holden Commodore VE VF V8 Sedan & Wagon dual 3in full system, coated 1 3/4in headers, 3.5in tips.
View part
Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1
MPI AutomotiveRRP$6502.43Holden Commodore VE VF V8 Ute & WM/WN Caprice Dual 3in Full System 1 3/4in HPC Extractors 3.5in Tips.
View part
Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in
MPI AutomotiveRRP$6443.54Holden DPE VF HSV 6.2L LSA Maloo ute dual 3in full system with 1 7/8in coated headers.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.