ford-falcon-ba-bf-sedan-g6e-xr6-2-1-2-catback-kit-inc-everflo-mufflers-dual-outl

FORD FALCON BA - BF SEDAN G6E XR6 2 1/2" CATBACK KIT INC EVERFLO MUFFLERS DUAL OUTLET

FORD FALCON BA - BF SEDAN G6E XR6 2 1/2" CATBACK KIT INC EVERFLO MUFFLERS DUAL OUTLET.

DistributorExhaust Systems Australia

Category: Mufflers and resonators

RRP $475.00 AUD
Confirmed on order
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
FORD FALCON BA - BF SEDAN G6E XR6 2 1/2" CATBACK KIT INC EVERFLO MUFFLERS DUAL OUTLET product image

Part specs

SKU
ford-falcon-ba-bf-sedan-g6e-xr6-2-1-2-catback-kit-inc-everflo-mufflers-dual-outl
Supplier
Exhaust Systems Australia
Category
Mufflers and resonators
Stock status
Confirmed on order

Finishing on a dual-outlet tailpipe, the Exhaust Systems Australia FORD-FALCON-BA-BF-SEDAN-G6E-XR6-2-1-2-CATBACK-KIT is a cat-back kit listed to fit the BA/BF Falcon sedan in G6E and XR6 trim. It carries two Everflo mufflers and splits to twin tips at the rear.

What makes this the dual-outlet kit?

The point of difference here is the rear: where a single-outlet kit exits one pipe, this version runs a dual outlet so the BA/BF sedan sits with two tips under the bar. Ahead of that it uses two Everflo mufflers to manage the note, making it a full cat-back replacement of the section from the catalytic converter back rather than a tailpipe-only swap. Because both Everflo mufflers sit in the cat-back run, the change is contained to the rear of the car and bolts to the factory mounting points the BA/BF was built around, which is part of why it goes in as a matched section rather than a custom fabrication.

What is a cat-back kit?

A cat-back covers the run from the catalytic converter rearward — the mufflers, intermediate pipe and tailpipe. It leaves the engine's emissions hardware ahead of the cat untouched, so it changes flow and tone through the back half of the car rather than the front.

Will it suit my G6E or XR6 Falcon?

It's listed to fit the BA/BF Falcon sedan in the G6E and XR6 grades. Body shape and hanger positions vary across the BA/BF run, so send your exact build and we'll confirm the dual-outlet tailpipe clears your rear bar before booking.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men supplies and fits this kit in-house across the Illawarra. We check the dual-outlet alignment, hanger rubbers and clearances on the hoist, and confirm the listing against your car. RRP is $475. This is a supplier part with a published RRP; if it isn't on the shelf we'll source it in, so flag your build early and we'll quote lead time and book the bay.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

Does this kit have one or two tailpipes?
Two — it's the dual-outlet version, exiting twin tips at the rear, fed by two Everflo mufflers.
Will it fit my BA/BF G6E?
It's listed to fit the BA/BF Falcon sedan in G6E and XR6 trim. Confirm your exact build with the workshop before ordering.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.