ford-falcon-fg-sedan-g6e-xr6-2-1-2-catback-kit-inc-hotdog-tailpipe

FORD FALCON FG SEDAN G6E XR6 2 1/2" CATBACK KIT INC HOTDOG & TAILPIPE

FORD FALCON FG SEDAN G6E XR6 2 1/2" CATBACK KIT INC HOTDOG & TAILPIPE for Performance Car - Ford.

DistributorExhaust Systems Australia

Category: Mufflers and resonators

RRP $275.00 AUD
Confirmed on order
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
FORD FALCON FG SEDAN G6E XR6 2 1/2" CATBACK KIT INC HOTDOG & TAILPIPE product image

Part specs

SKU
ford-falcon-fg-sedan-g6e-xr6-2-1-2-catback-kit-inc-hotdog-tailpipe
Supplier
Exhaust Systems Australia
Category
Mufflers and resonators
Stock status
Confirmed on order

FORD-FALCON-FG-SEDAN-G6E-XR6-2-1-2-CATBACK-KIT-INC-HOTDOG-TAILPIPE is a cat-back kit built around a hotdog resonator rather than a full chambered muffler, which is what shapes its character. Supplied by Exhaust Systems Australia in a 2in bore, it's listed to fit the Ford Falcon FG sedan in G6E and XR6 trim.

Why a hotdog instead of a muffler?

The defining piece here is the hotdog — a compact straight-through resonator that flows freely and trims a specific frequency band rather than broadly absorbing volume the way a chambered muffler does. On the FG sedan that means the kit leans towards a freer-breathing, more open character through the rear section, paired with the supplied tailpipe to finish the run. It's the resonator-led path for an owner who wants flow and a cleaner note over heavy silencing.

What does a 2in cat-back replace?

A cat-back kit replaces everything from the catalytic converter back to the tailpipe, leaving the cat and front pipework untouched. At a 2in bore it's matched to the FG's straight-six output rather than a big-bore build, keeping gas speed sensible for road driving. The hotdog and tailpipe arrive as a kit so the rear of the system goes on as one matched run.

Will it suit my Falcon FG sedan?

It's listed to fit the FG Falcon sedan in G6E and XR6 specification. The FG ran the Barra six in these trims, and this kit is cut for the sedan body and its rear routing. Falcon variants differ between sedan, ute and wagon, so confirm your exact build, trim and any prior exhaust work with the workshop before ordering.

What does fitting involve at our Illawarra workshop?

Oak Flats Muffler Men supplies and fits this kit in-house across the Illawarra. We check the hangers and rubbers, mate the hotdog and tailpipe to your existing front section, and set the alignment so the tip sits square. Bring the car in and we'll confirm clearances and book the bay.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

What's the difference between the hotdog and a normal muffler?
The hotdog is a straight-through resonator that flows freely and cuts a target frequency, where a chambered muffler reflects and absorbs more broadly for quieter running. This kit uses the hotdog, so it favours flow and a more open note.
Does this kit keep my catalytic converter?
Yes — it's a cat-back kit, so it replaces from the catalytic converter rearward and leaves the cat and front pipework in place.
Will it fit my FG sedan?
It's listed to fit the Ford Falcon FG sedan in G6E and XR6 trim. Confirm your exact variant with Oak Flats Muffler Men before ordering.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.