KBD9025-XXXX

Mitsubishi Pajero NX (4M41T) 3.2L Turbo Diesel Oct 2016 to Nov 2021 DPF Model - 3 Inch

Mitsubishi Pajero NX (4M41T) 3.2L Turbo Diesel Oct 2016 to Nov 2021 DPF Model - 3 Inch (DPF Back) Exhaust System with Straight Through No Mufflers.

BrandPacemaker

Category: Mufflers and resonators

RRP $1291.84 AUD
Confirmed on order
Afterpay, Zip Pay & Zip Money available
Afterpay acceptedZip accepted — Zip Pay and Zip Money
Mitsubishi Pajero NX (4M41T) 3.2L Turbo Diesel Oct 2016 to Nov 2021 DPF Model - 3 Inch (DPF Back) Exhaust System with Straight Through No Mufflers product image

Part specs

SKU
KBD9025-XXXX
Supplier
Pacemaker
Category
Mufflers and resonators
Vehicle fitment
Mitsubishi NX
Stock status
Confirmed on order

The Pacemaker KBD9025-XXXX is the bare-pipe option in the NX dpf-back range: a 3in straight-through for the DPF-model Mitsubishi Pajero NX (4M41T 3.2L turbo-diesel, 2016) that carries no muffler and no resonator at all.

What you get — and give up — with a bare-pipe build

Removing every silencing device leaves the smoothest path for gas from the particulate filter to the tailpipe, and it makes this the loudest member of the NX family. There is a clear trade here: maximum simplicity and flow in exchange for a harder, more present diesel note at every load. Owners who pick it tend to want the cleanest pipe rather than the most refined cabin.

How a DPF-back interfaces with the later NX

On the DPF-equipped NX, a dpf-back picks up behind the diesel particulate filter and carries through to the tail, so the DPF and everything upstream stay as Mitsubishi fitted them. Pacemaker sizes this run at 3in and lists it for the DPF-model NX specifically, matching the later car's filter interface rather than the pre-DPF layout.

Confirming fit on your NX Pajero

It is listed to fit the Mitsubishi Pajero NX, DPF model, 4M41T 3.2L turbo-diesel, from 2016. Feed listings can drift, so we check your exact build, transmission and any earlier exhaust work against the part before placing the order.

Fitting it at our Illawarra workshop

Oak Flats Muffler Men installs this Pacemaker dpf-back on site in the Illawarra. With no silencing in the run we make a point of describing the volume for your driving before you commit, then fit the pipework and seal the joints so the bare-pipe build sits and flows as intended.

Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.

Common questions

How loud is the bare-pipe KBD9025-XXXX?
With no muffler or resonator it is the loudest build in the NX dpf-back family. We will walk you through the note before you order so there are no surprises.
Could I soften it afterwards?
If the open note proves too much, talk to the workshop about the resonator build for the same NX — we will help you weigh the swap.

Fitment support across the Illawarra

Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.
Show nearby fitment areasCollapse section

Book the right exhaust job without guessing.

Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.