Holden Commodore VE - VF Sedan July 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2
PacemakerRRP$4891.13Holden Commodore VE - VF Sedan July 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2 1 3/4" 4 into 1 Headers 3" System (PP5381-61) at $4891.13 RRP
View partPP5361-29
Holden VY Series 2 - VZ 5.7 8 Cylinder Ute 1 3/4" Tuned Headers 2 1/2 Inch System
Holden VY Series 2 - VZ 5.7 8 Cylinder Ute 1 3/4" Tuned Headers 2 1/2 Inch System.
BrandPacemaker
Category: Extractors and headers
RRP $4339.16 AUD
Confirmed on orderAfterpay, Zip Pay & Zip Money available
Part specs
- SKU
- PP5361-29
- Supplier
- Pacemaker
- Category
- Extractors and headers
- Vehicle fitment
- Holden VY VZ
- Stock status
- Confirmed on order
Pacemaker PP5361-29 is a 1¾in tuned-length header pack with a full 2½in system, listed to fit the Holden VY Series 2 / VZ 5.7-litre V8 ute. The 2½in pipe size is the call that defines this one — sized to keep gas speed up for street response rather than chasing top-end on a built engine.
Why a 2½in system on a 5.7 ute?
A 2½in system holds exhaust velocity through the mid-range, which is where a road-driven 5.7-litre V8 ute spends most of its time — off the lights, through the gears, towing or loaded. Paired with the 1¾in tuned-length primaries, it favours throttle response and a fuller note over the last few hundred rpm of a race-only setup. PP5361-29 runs the complete system back from the headers, so it's the engine-back change, not a tailpipe swap.
What are tuned-length headers?
Tuned-length headers replace the restrictive cast factory manifolds with equal, mandrel-bent primary runners that merge in a measured collector. The 1¾in primary is the everyday-V8 bore — it scavenges each cylinder cleanly without bleeding low-down torque. On the VY/VZ ute platform the runners are routed to clear the chassis and steering for that body.
Will it suit my Holden ute?
It's listed to fit the Holden VY Series 2 and VZ 5.7-litre V8 ute. The supplier doesn't break the listing down to a build year or exact variant, so we treat fitment as listed-to-fit and confirm it against your actual ute — engine, gearbox and what's already under it — before anything is ordered.
Is it road legal, and what does fitting involve?
These are headers and pipework, not an emissions device — there's no catalytic converter or muffler certification published with this listing, so whether your finished ute meets NSW requirements comes down to how the whole system is configured and signed off. Oak Flats Muffler Men fits Pacemaker systems like this across the Illawarra. Listed RRP is 4,339.16 AUD; the fitting charge is quoted once the ute is on the hoist.
Stocked and fitted by Oak Flats Muffler Men, the Illawarra exhaust and 4x4 specialist in Oak Flats, NSW.
Common questions
- What size is the system on the PP5361-29?
- A full 2½in system running back from 1¾in tuned-length headers, listed for the VY Series 2 / VZ 5.7 V8 ute.
- Does this fit the 6.0-litre ute?
- This listing is the 5.7-litre VY Series 2 / VZ ute fitment. Tell us your exact engine and we'll match the right Pacemaker part number.
Fitment support across the Illawarra
Fitment checks near you across 18 Illawarra suburbs, from Oak Flats and Shellharbour to Wollongong and Kiama.Show nearby fitment areasCollapse section
Oak Flats Muffler Men can check this part against supplier specs, part number, image, RRP and vehicle details for customers around Oak Flats, Shellharbour, Wollongong, Dapto, Albion Park, Kiama and the northern suburbs.
Check fitment near Oak FlatsCheck fitment near Albion Park RailCheck fitment near ShellharbourCheck fitment near WollongongCheck fitment near DaptoCheck fitment near WarillaCheck fitment near CorrimalCheck fitment near WoononaCheck fitment near BulliCheck fitment near ThirroulCheck fitment near KiamaCheck fitment near Albion ParkCheck fitment near Lake IllawarraCheck fitment near Mount WarrigalCheck fitment near Barrack HeightsCheck fitment near Barrack PointCheck fitment near BlackbuttCheck fitment near Flinders
Related parts in this category
More extractors and headers the workshop supplies and fits. Send the vehicle and the part you are weighing up for a fitted quote.
Holden Statesman WM - WN From Aug 2006 - Oct 2017 Series I And Series II
PacemakerRRP$4891.13Holden Statesman WM - WN From Aug 2006 - Oct 2017 Series I And Series II fitted with 6.0 - 6.2 V8 1 3/4" 4 into 1 Headers 3" System.
View part
Holden VE -VF Ute 2007-2017 6.0 Gen IV - 6.2 LS3 V8 1 3/4" 4 into 1
PacemakerRRP$4891.13Holden VE -VF Ute 2007-2017 6.0 Gen IV - 6.2 LS3 V8 1 3/4" 4 into 1 Headers 3" Ute System.
View part
Holden Commodore VE - VF Wagon July 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2
PacemakerRRP$4891.13Holden Commodore VE - VF Wagon July 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2 1 3/4" 4 into 1 Headers 3" Wagon System (PP5381-69) at $4891.13 RRP.
View part
Holden Commodore VE - VF Sedan Jul 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2
PacemakerRRP$4891.13Holden Commodore VE - VF Sedan Jul 2006 - Oct 2017 Gen IV 6.0 - LS3 6.2 V8 1 7/8" 4 into 1 Competition Headers 3" Sedan System (PP5382-51)
View part
Holden VE -VF 8 Cylinder 6.0L / 6.2L Gen IV, LS2, LS3, Ute 1 7/8 Tuned
PacemakerRRP$4891.13Holden VE -VF 8 Cylinder 6.0L / 6.2L Gen IV, LS2, LS3, Ute 1 7/8 Tuned Headers 3" Inch System.
View partBook the right exhaust job without guessing.
Send the vehicle make, model, year, engine, current issue, desired sound or performance goal, and clear photos of the existing exhaust where available.